Remplacement pentium D par core 2 duo

Sfynx

Habitué
Bonjour, j'ai un pc équipé d'un Pentium D 3,4 GHZ que je voudrais remplacer par un core 2 duo E6600.

J'ai deux questions,

1/ Le socket actuel étant bien un 775, le processeur fonctionera-t-il avec ma carte mère?

2/ La différence de puissance et de rapidité est-elle réellement intéressante?

Merci d'avance,

Sfynx
 

countzero

Expert
1)Non pas forcément, il faut que le chipset de ta carte mere s775 soit compatible c2D. Le mieux est de nous donner le nom de ta carte mère.
2) Tout dépend de l'utilisation que tu en fait. Le pentium D n'est pas si a la ramasse que ça et si tu as une bonne carte graphique pour les jeux qui compense la faiblesse relative de ton processeur, c'est peut-être pas forcément si urgent de changer.
 

Sfynx

Habitué
Voici les spécifications de ma carte mère

NVIDIA® C19 and CK804 chipset and the Intel® Pentium® 4 processors in the LGA775 socket, code-named Prescott and Smithfield.

Microprocessor



Microprocessor type Intel® Pentium® 4 Extreme Edition with Hyper-Threading (HT) Technology or dual-core processing

NOTE: Not all Pentium 4 processors support HT Technology and/or dual-core processing.

Cache 512 KB, 1 MB, or 2 MB



Memory



Type 533 and 667 MHz DDR2 unbuffered SDRAM

Memory connectors Four

Memory capacities 256 MB, 512 MB, 1 GB, or 2 GB non-ECC

Minimum memory 512 MB

Maximum memory 2 GB – Windows® XP 32-bit

8 GB – Windows XP 64-bit

BIOS address F0000h



Computer Information



Chipset NVIDIA nForce® 4 SLI™ C19/CK804

DMA channels Five

Interrupt levels 24

BIOS chip (NVRAM) 4 Mb

NIC Integrated network interface capable of 10/100/1000 communication

System clock 800 or 1066 MHz data rate (depending on processor)



Video



Type Dual PCI Express® x16



Audio



Type NVIDIA® AC '97 7.1 channel (Realtek™ ALC850)



Expansion Bus

Bus type PCI 32-bit

PCI Express x1 and x16

Bus speed PCI: 33 MHz

PCI Express: 2.5 Gb/s raw bandwidth (bidirectional) per lane

Bus throughput PCI Express:

x1 slot bidirectional speed – 500 MB/s

x16 slot bidirectional speed – 8 GB/s

PCI Connectors Three

Connector size 120 pins

Connector data width (maximum) 32 bits

PCI Express Connectors One x1

Connector size 36 pins

Connector data width (maximum) One PCI Express lane

PCI Express Connectors Two PCI Express x16

Connector size 164 pins

Connector data width (maximum) 16 PCI Express lanes



Drives



Externally accessible One 3.5-inch drive bays

Three 5.25-inch drive bays

Internally accessible Three bays for 1-inch–high hard drives

Available devices Serial ATA drive, floppy drive, memory devices, CD drive, CD-RW drive, DVD drive, DVD-RW drive, and DVD and CD-RW combo drive, media card reader



Connectors



External connectors

IEEE 1394 Front and back panel 6-pin serial connectors

Network adapter RJ-45 connector

PS/2 (keyboard and mouse) Two 6-pin mini-DIN

Serial 9-pin connector

USB Two front panel, six back panel, and two internal USB 2.0-compliant connectors

System board connectors

IDE drive One 40-pin connector

Serial ATA Four 7-pin connectors

Floppy drive 34-pin connector

Fan Four 5-pin connectors

PCI Three 120-pin connectors

PCI Express x1 36-pin connector

PCI Express x16 Two 164-pin connectors



Controls and Lights



Power control Push button

Power light Green light – Blinking green in sleep state; solid green for power-on state

Amber light – Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem



Hard-drive access light Green

Link integrity light (on integrated network adapter) Green light – A good connection exists between a 10 Mbps network and the computer

Orange light – A good connection exists between a 100 Mbps network and the computer



Yellow light – A good connection exists between a 1 GB (or 1000 Mbps) network and the computer.



Off (no light) – The computer is not detecting a physical connection to the network



Activity light (on integrated network adapter) Yellow blinking light when there is activity on the network. If there is not any network activity, the light is off.

Diagnostic lights Four lights on the front panel

Standby power light AUXPWR on the system board

Case backlight Color options: off (no light), ruby, emerald, sapphire (default), amber, amethyst, topaz, diamond



Power



Wattage 650 W

Heat dissipation 1000 BTU/hr

Voltage Fixed-voltage power supply – 110 V at 50/60 Hz

Manual selection and auto-sensing power supplies – 90 to 135 V at 50/60 Hz; 180 to 265 V at 50/60 Hz; 100 V at 50/60 Hz for Japanese computers



Backup battery 3 V CR2032 Lithium coin cell



Physical



Height 49.1 cm (19.3 inches)

Width 22.2 cm (8.7 inches)

Depth 48.8 cm (19.2 inches)

Weight 19 kg (42 lbs)



Environmental



Temperature

Operating 10° to 35° C (50° to 95° F)

NOTE: At 35° C (95° F), the maximum operating altitude is 914 m (3000 ft).

Storage –40° to 65° C (–40° to 149° F)

Relative humidity 20% to 80% (noncondensing)

Maximum vibration

Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min

Storage 0.5 G at 3 to 200 Hz at 1 octave/min

Maximum shock

Operating Bottom half-sine pulse with a change in velocity of 50.8 cm/sec (20 inches/sec)

Storage 27-G faired square wave with a velocity change of 508 cm/sec (200 inches/sec)

Altitude

Operating –15.2 to 3048 m (–50 to 10,000 ft)

Storage –15.2 to 10,668 m (–50 to 35,000 ft)


J'ai deux 7900 GTX en SLI

Merci d'avance

Sfynx
 

countzero

Expert
Bon tu as un chipset nforce4 sli intel. Tu as une carte un peu près similaire à une Asus P5N32-SLI. A la base ce n'est que pour les p4 et PentiumD. Mais j'ai l'impression que ta carte est une version revision. Il y a la mention C19/CK804. Cela la rend peut être compatible c2D.
Regarde ce lien :



C'est peut etre ta carte, une version révisée du nforce4sli qui le rend compatible c2d
Ce serait plus simple si avec everest tu nous donnais le nom exact de ta carte mère
 

boub popsyteam

Grand Maître
A moins que dell ne dise que c'est compatible, ça ne l'est pas :o

Il faut que le bios le gère et qu'il ai le bon microcode sans parler des regulateurs de tensions.
 

Sfynx

Habitué
:-( Je vois, tant pis pour moi, je ne changerais pas mon proc........ et je resterais avec Mon Pentium D jusqu'à ce que mort s'en suive...

Merci beaucoup en tous cas pour ces infos...

Dernières question, vous pensez que ça peut le faire d'overclocker mon proc? J'ai entendu dire que cette série n'était pas très faite pour...?
 

Sfynx

Habitué
yanis, tu veux dire, que ma carte, en l'état et sans changer ou flasher le Bios supporte un core 2 duo?
 

broukmout

Grand Maître
nan, yanis il à lu le topic en diagonale et il te raconte une connerie, etant donné que tu n'as pas un p5n32.
 

Sylvain37

Grand Maître
Ta carte mère est incompatible Core 2 Duo malgré la mise à jour du bios sur .
La réponse à ta question :
 
Vous devez vous inscrire ou vous connecter pour répondre ici.
Derniers messages publiés
Statistiques globales
Discussions
730 133
Messages
6 718 046
Membres
1 586 390
Dernier membre
HarryMag
Partager cette page
Haut